Jump to content

Sign in to follow this  
cttc

Foxtel Faq - Setup & Use (& Optus Digital)

Recommended Posts

Other than the optical port that DS250 looks identical to the DS230 that we have had here in NZ (SkyNZ) for a couple of years now.

Cyril

Share this post


Link to post
Share on other sites
Cant see where to edit my post, but my first pic was meant to be this one.

Thanks for the info updated the FAQ.

Share this post


Link to post
Share on other sites
I stand by my advise, connect using YUV via the DB15 connector and your on your way. If you chose RGB you need a H&V sync seperator and achieve nothing.

This leaves your PC to feed the DVI input, and the Foxel box to feed YUV (Component) into the VGA connector. Dont go down the RGB over VGA line, it will not benifit you one dot.

Cyril

Thank you very much cyril

Share this post


Link to post
Share on other sites


Hi

My foxtel keeps going to no signal or flickering on my TV AV input not on the foxtel signal. I've tried changing leads, swapping connections, tried a set top box through that av and it works fine. So i'm thinking the AV input has a problem.

It happens alot on sports replays on foxtel.

Any help would be appreciated

Share this post


Link to post
Share on other sites
My foxtel keeps going to no signal or flickering on my TV AV input not on the foxtel signal.

Try with a different cable from a different Foxtel STB output (eg use the VCR scart composite output, or the RCA composite output if your box has one) to narrow the problem. It might just be your Scart cable so try the one plugged into your VCR scart if you have one. Which Foxtel box is it?

Share this post


Link to post
Share on other sites
Try with a different cable from a different Foxtel STB output (eg use the VCR scart composite output, or the RCA composite output if your box has one) to narrow the problem. It might just be your Scart cable so try the one plugged into your VCR scart if you have one. Which Foxtel box is it?

I've tried the different outputs only thing I was going to try is scart out of foxtel box to component.

Not sure what box it is grey box with smart card on left hand side at front.

Thanks

Share this post


Link to post
Share on other sites


Does anyone know if it is possible to get your foxtel to switch state feeds.

I am desperately wanting to get NSW ch9 not Vic.

Just wondering if this is something that is programmed on the card, the box or the sat feed itself to this region.

Cheers,

Dan

Share this post


Link to post
Share on other sites

The card has details that were programmed based on your residential address. Doubt you can readily have it changed, for legal broadcast region reasons.

Cyril

Share this post


Link to post
Share on other sites


I had a Foxtel IQ box installed on Monday and have found this thread to be of great help in understanding the gamut of PVRs, STBs, etc.

Many thanks to the contributors, particularly 'cttc' for the excellent oversight.

Les Harris

Vic

Share this post


Link to post
Share on other sites

Need help RE: Foxtel installation.

Around 2000-2001, we had foxtel and moved to a new house right near Kincumber mountain..the foxtel guy said apparently we couldn't get reception because of where we now live.

Now back then Foxtel was analog, its now digital..

Foxtel is coming out on Saturday for install, what are my chances of it going ahead?

I have seen alot of other houses with interferance with mountains and trees so I don't understand, hopefully its different with digital.

Thankyou.

P.S. - I tried to start a new topic but it didn't let me.

Share this post


Link to post
Share on other sites

PSI-11D, it's quite possible cable may be available in your area, which should give you everything that Satellite offers.

Share this post


Link to post
Share on other sites


im on the central coast, nsw..i dont think cable is avaliable..so will there be problems if i can only get satelite?

Share this post


Link to post
Share on other sites
im on the central coast, nsw..i dont think cable is avaliable..so will there be problems if i can only get satelite?

I can't see what sort of problems there would be being on a mountain, unless your specific location prevents clear line-of-sight to the Foxtel sat. See what the techie says - if it can't be installed I'm sure they won't charge you.

Share this post


Link to post
Share on other sites

Im not worried about the charge - Its free anyway.

Im just hoping that its different this time around. Im actually below a mountain...but the thing is, Ive seen alot of other dishes pointing straight at trees, mountains etc and they have it hooked up..why did the tech not even bother to go on the roof to try?

Fingers crossed. :blink:

Share this post


Link to post
Share on other sites

The angle of incidence of the beam from 156E (Optus C1) in your location is 50-51deg depending on your exact location, with an azimuth of around 9-10deg so if you lookup at an angle of 50deg in the northern sky can you see without obstuction, if so then all should be fine.

If you make a simple triangle with a piece of cardboard that has a base length of 100mm and a vertical length of 120mm (thus a hypotenuse of 156mm) then you will have a 50deg triangle. Hold this level, helps if you have a spirit level, and look up the hypotenuse, if you see clear sky roughly 9deg to the east of north (real north) then all should be ok.

Dont forget that KU band dishs are offset dishes, as such the LNB arm points some 20odd degrees below the angle of beam incidence.

Cyril

Share this post


Link to post
Share on other sites

Hi - anyone able to help me out here?

I got foxtel installed last week. Looks like a UEC box (its got a sticker saying DN 1000 attached) so I presume its a UEC 1000? I'm connecting to a new Samsumg M81 LCD. Picture quality using the std Scart to Composite is pretty average so I bought a Scart to Component cable on the advice of the foxtel guy. Followed the instructions from foxtel to set up the component connection (changing the picture output from PAL to YUV) but the picture I get is shocking. I have reverted back to using my new cable as a composite output at this stage.

Any suggestions where I could be going wrong ?

Thanks to any good samaritans out there

Cheers

Z

Edited by zinc

Share this post


Link to post
Share on other sites

Only thing I can suggest is to make sure you have the cable going from the TV scart and not the VCR scart.

Just reread your post. How can you revert to using your new cable (which presumably has 5 leads) as composite???

Share this post


Link to post
Share on other sites

Things I would try:-

Make sure you select save settings after changing to YUV.

As Venus said make sure your using TV scart.

Make sure your plugging the component cables into correct sockets on TV.

Try the other component input on the TV.

Disconnect the composite cable (ie don't have both component and composite connected at same time).

Maybe even do a firmware update on the box.

Otherwise maybe you have dud cable or dud box.

Just reread your post. How can you revert to using your new cable (which presumably has 5 leads) as composite???

The Foxtel Scart to component cable has 6 (3 component 2 audio and 1 composite).

Share this post


Link to post
Share on other sites
The Foxtel Scart to component cable has 6 (3 component 2 audio and 1 composite).

Thanks for that. I haven't seen the Foxtel-branded cable; only the typical 3 component plus R/L Audio.

Share this post


Link to post
Share on other sites

So if I get Foxtel hooked up now and buy a DVD recorder later, how easy will it be for me to set it up to record? I'm great at using technology but crap at setting it up!! :blink:

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...