Jump to content

noddou

Members
  • Content count

    46
  • Joined

  • Last visited

Community Reputation

6 Neutral

About noddou

  • Rank
    10+ Post Club

Profile Fields

  • Location
    4710
  • Country
    australia

Recent Profile Visitors

1,142 profile views
  1. Hi Mike ,by any chance do you have any drawings or photos of the mods that were made ?
  2. Hi Wimbo what are your thoughts on the E-50's ?
  3. all sounds alitte out of my league,doubt I have sufficent experience for this task... thankyou for the feedback
  4. Thanks Steve , appreciate the advice
  5. Hi Everyone Has anyone done this mod ? If so would it be able to get some details on what to do ? I have to general idea on what to remove,however not what to put inline whether its a cap or resistor and what specs would they be ? 'Yes .I'm a novice Cheers and thankyou
  6. Thankyou everyone for your inputs ..... Cheers
  7. Good evening All Been giving thought to maybe I would get an improvement if there is an increase in the interconnect wires between the crossover and the terminals of the speakers,currently wire diameter is O.D 1.5 mm, inner wire O.D 0.75mm It just seems remarkably small wires in place , in know with fluids an increase connecting hoses will improve performance (of course the end use will determine if its an improvement),would there be an improvement if the wire diameter was increased ? If so, what recommendations for sizing or wire type ? This is on a pair of Wharfdale E50 speakers ,which I'm reviving. Cheers everyone
  8. Good evening All Been giving thought to maybe I would get an improvement if there is an increase in the interconnect wires between the crossover and the terminals of the speakers,currently wire diameter is O.D 1.5 mm, inner wire O.D 0.75mm It just seems remarkably small wires in place , in know with fluids an increase connecting hoses will improve performance (of course the end use will determine if its an improvement),would there be an improvement if the wire diameter was increased ? If so, what recommendations for sizing or wire type ? This is on a pair of Wharfdale E50 speakers ,which I'm reviving. Cheers everyone
  9. Hi All I was given a Sanyo MR-920 reel recorder,this is to be my re-entry into this world after alonggggggggggggggg time,actually quite keen to start but first... could anyone help with details ,specs sheets or manuals , or experiences/knowledge , hints, tips or tricks with this model . as well recommendations for new reel tape . It's believed when last working the play head wasn't working ,so that's one fault ,my other concern is for starting this up after quite some years ,what procedures are best followed after basic check by a sparky. Any and all positive feed back is much welcomed Cheers Doug Pictures:
  10. Dear members I have a dual 1249 ,unfortunately got it without any of the original paperwork although have the manuals downloaded I'm some what confused as to the correct power supply (voltage to use) , there is supposed to be a switch to be able to changeover to 240v but there isn't. Also the power cord has a 125v plug and is wired direct BUT there is a label telling me its 240v , along with this the manual mentions if power supply switched from either power frequency there is a change of the drive pulley and resetting the strobe required If anyone can assist would be wonderful Cheers Noddou See Photo attached
  11. noddou

    Mods for Wharfedale E-50

    Thx for the responses Initially I'll install braces front to back ,the original lining in the speakers is foam around the sides and top nothing on the bottom ,this I want to change out though just what is undecided ,the biggest prob I have is with crossover ,I'm not sure I have the skill level yet to under take any mods,help with this would great Cheers
  12. Hi everyone I'm asking if there is anyone who has done any modification to these speakers seeking advice if anyone has done any internal bracing ,internal damping or upgrades on the crossover ? or even recommendations in regards to any of these ideas. cheers in-advance and thankyou
  13. noddou

    Speed Check

    Hi all yes i could very well need a new belt Eltech or a combination .... tho my main reason for asking was to find a method or device for checking, other than this deck but also i have a Dual 1219 and Technics SL1900 many thx to all that have replied
  14. noddou

    Speed Check

    Thankyou everyone i'll be looking into each of the options and Johnmath's technical advice will not go astray ..Ty John Gezzz your got be glad your a member of Stereonet :D Cheers and best wishes to you all
×