Jump to content

malamute

Full Member
  • Content Count

    6
  • Joined

  • Last visited

Community Reputation

1 Neutral

Profile Fields

  • Location
    Canberra
  • Country
    Australia

Recent Profile Visitors

577 profile views
  1. Thanks Betty Boop, not in a rush and want to do it right just once, so looks like I have a bit of a wait for some to be certified then.
  2. I have also been checking out 10m hdmi cables. Hdmi 2.1 / 48gbps one I found (33 feet in this case) for $258. https://www.amazon.com.au/dp/B07SFCH81K Or there was a 50 foot monoprice one but that cost more. So depends if you think you will need hdmi 2.1 in the future, if it might be worth looking at those.
  3. My current setup is an older 55 inch 1080p oled TV, with a denon avr-x3100w in a very large cupboard with my network gear. And speaker cables then heading back to the TV room. Telstra TV and old roku to the avr, then hdmi to the TV over Ethernet / Cat6 (hdbaset). At some point I will upgrade my TV to a new 4k lg oled. At that point I wl also have to update my connection between TV and avr. My current one only does 1080p and doesn't do ARC. So then my question is, how well does ARC work in general, and especially if anyone uses it over hdbaset? I would prefer to use the TV apps with sound returning back to the avr. If possible to a newer receiver that supports atmos. So passing Dolby digital + via streaming services. I don't think there is any hdbaset that supports earc yet, and perhaps it never will as bandwidth over a single Cat6 is too limited? So my options I see are: - new hdbaset sender/receiver that supports arc, use TV apps and send sound back to avr using arc. - new hdbaset sender/receiver that supports 4k, use a new device eg shield TV or apple TV attached to avr, send 4k video signal to TV over hdbaset. - get a cabler in to put a new hdmi 2.1 cable between TV and avr (about 10m). Has to get down a wall where existing cabling is but no conduit or rope to pull. Then I can use source in either end ok. How solid would a 10m hdmi cable setup be? Any other ideas are welcome.
  4. Further information: Manual at https://www.manualslib.com/manual/828051/Pioneer-Vsx-1016v-K.html?page=6#manual https://www.manualslib.com/manual/130515/Pioneer-Vsx-1016v-K.html Continuous Power Output – Stereo Front. . . . . .. . . 150 W + 150 W (DIN 1 kHz, THD 1 %, 6 Ω) Continuous Power Output – Multichannel (DIN 1 kHz, THD 1 %, 6 Ω) Front. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 W + 150 W Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 W Surround . . . . . . . . . . . . . . . . . . . . . . .. . . . 150 W + 150 W Surround back . . . . . . . . . . . . . . . . . . . .. . . 150 W + 150 W B Rated Power Output – Stereo (20 Hz to 20 kHz, 0.09 %, 8 Ω) . . . . . . . . . . . 140 W+140 W MCACC audio calibration. Dolby Digital and DTS decoding, including Dolby Digital EX, Dolby Pro Logic IIx, DTS 96/24 and DTS-ES Has hdmi but pretend it doesn't, early days of hdmi and I don't think those inputs are of much use. Better to use the optical inputs. Heavy receiver so pick up only. Photos:
  5. I bought Denon AVR-S750H from them and it had the normal Qualifi warranty card in there.
  • Classifieds Statistics


    Currently Active Ads

    Total Sales (Since 2018)

    Total Sales Value (Last 14 Days)

    Total Ads Value (Since March 2020)
×
×
  • Create New...